Gas stove energy-saving burner is a necessary tool adopted by many families, it not only has excellent energy-saving and emission reduction advantages, and according to the actual use experience of users, it seems that the performance of gas stove energy-saving burner is also excellent, which can meet the daily life needs of most families, and has become one of the practical home improvement equipment. Today we bring you the information about the replacement steps of gas stove energy-saving burner and the disassembly method of Sakura gas stove burner in two panels.
One, how to replace the energy-saving stove head of the gas stove
How to replace the energy-saving stove head of the gas stove.
Folded installation of the stove head. Tempered glass panel is generally fixed around the stove head, take off the pot holder and decorative ring first, open the fixing screws around the stove head in turn, and the panel can be removed. The disassembly of the stove head is even simpler, just open the set screws in turn, back to install, to be installed in reverse order in turn.
Cleaning of the pot. The pot that needs to be replaced is dirty, which will affect both the combustion quality and the solidity of the bonding, and must be thoroughly cleaned. First, use a hammer to crack the old pottery pieces, and then the fully soaked pot (the recommended time is 24 hours) for cleaning. A wire ball, screwdriver, toothbrush, test tube brush and other tools can be used with the cleaning, taking care not to scratch or pry off the enamel.
After cleaning the can must be dried before bonding, if time is short, can be put on the stove with a slight fire drying.
Use the manufacturer’s special bonding mud (water glass + talc modulation) bonding, the order of application of bonding mud is first can body, after the pottery, as far as possible to wipe into a natural slope; wipe a good adhesive to take suitable moisturizing measures, the entire application time should be controlled in about 10 minutes. Some brands recommend users to stick with toothpaste, the practice results in insufficient firing resistance.
After the coating is completed, the pottery pieces are fed into the pot slowly and in a balanced manner. The process of pressing together should avoid point pressure, double side pressure, and recommend a large area of palm push pressure, same side pressure. When the ceramic piece is pressed flush with the upper plane of the pot, the positioning work is over.
Seal the edges. Use fingertip glue to quickly make up glue along the joint surface of the pottery piece and the pot body to level.
Natural drying, the recommended time is 12 to 24 hours. Visual inspection, if there are any gaps, need to fill the glue again.
Sintering. Once the pot is in place, it can be fired and sintered. Recommend the first burning 5 ~ 10 seconds, flame out half a minute; second burning 30 seconds, flame out half a minute; third burning 5 ~ 10 minutes.
Second, how to remove the Sakura gas stove burner
Gas equipment maintenance, improper operation caused by the consequences of the accident is terrible, it is not recommended that personal repair, disassembly, the money can not be saved. Send you a paragraph “town gas management regulations” of the relevant provisions.
Article 32
Gas combustion appliances production units, sales units shall establish or entrust the establishment of after-sales service sites, equipped with qualified gas combustion appliance installation, maintenance personnel, responsible for after-sales installation, maintenance services.
Installation and maintenance of gas combustion appliances, shall comply with relevant national standards.
Sakura’s gas stove (SCG6781S) stove and the stove plate without any screw connection between the stove and the stove plate is two tubular cylindrical set, can be directly up to take out the stove, if the use of a long time, you need to lightly knock the old stove to loosen it after removal.
About the gas stove energy-saving stove specific repair and disassembly method, we need to refer to the relevant aspects of the regulations introduced, in addition, should also be in the actual operation process combined with specific situations, such as the brand of gas stove energy-saving stove models and differences in the use of the environment and so on several board information, so as to determine the appropriate steps, when necessary, you can also turn to the relevant professionals, in order to be able to reasonable Operation, as far as possible to reduce unnecessary trouble and losses.
