After the owner purchases the toilet, the installation service is generally included, but there are still many points to pay attention to during the installation process, so as to avoid quality problems in the future. Let’s take a look at the detailed toilet installation steps together!
1. Toilet installation steps
1. Check the toilet installation environment
Before installing the toilet, be sure to check it thoroughly to see if the sewer pipe is unobstructed, and to see if the place where the toilet is installed is level. If it is not level, then it must be leveled when installing the toilet. In addition, the sewer pipe opening of the toilet generally leaves a large section, and the excess pipe is cut short, leaving about 3mm above the ground. Also, check whether the size of the toilet you bought matches the reserved space in your home. After these inspections, the toilet installation can begin.
2. Check the toilet installation sewage outlet
After confirming, make a mark on the sewage pipe of the toilet seat and the sewage pipe of the sewer, determine the installation position of the toilet, make a hole with an electric drill, and bury the expansion screw in it. Then install a sealing ring on the sewage outlet of the toilet, and install glue or cement slurry on the sewage pipe to ensure that the sewage will not seep out. These methods and steps are to test your knowledge of the toilet and the parts of the toilet. Only when you understand it will it be convenient for you to install the toilet. After completing the above steps, don’t worry, take your time.
3. Align the toilet drain pipe
Align the toilet sewage pipe you marked with the sewer sewage pipe, and install a ring of sealing ring or glass glue at the bottom of the toilet on the toilet installed to ensure that the pipe of the toilet can match the nozzle of the sewer , and is stable. After these two super important steps are installed, the following follow-up work will be simple. Do you think that the introduction of the editor is very simple, as long as you understand the inner structure of the toilet, these are just small knowledge.
4. Install toilet parts
Just install the parts or accessories of the toilet. Screw on the screw at the installation place of the toilet, install and debug the fittings of the water tank, and connect the water pipe in the bathroom. Before that, be sure to check whether the water valve switch in your home is normal, check whether the toilet water pipe connected to the water valve is normal, whether the length is long enough, etc., when installing the water pipe, it must be tight and there is no leakage. Leakage to prevent water leakage when pumping. Although there are only some small details, the details determine the quality of the installation.
5. Debug toilet
The last step is also the easiest and easiest one. The installation of the toilet is basically completed by this time, and the rest of the time is to debug the toilet to see if the drainage pipe is unobstructed, whether there is any blockage, and whether the water can be pumped normally. In addition, if there are still some problems during the debugging process, You can refer to the manual for repairs. The general toilet installation manual can explain in detail every possible problem and solution when the toilet is installed. Although the editor is not omnipotent, there is no problem in solving basic daily chores.
Second, the toilet installation process
1. Check the levelness of the sewage pipes and the ground
Before installing the toilet, you should conduct a comprehensive inspection of the sewage pipes to see if there are mud, sand, waste paper and other sundries in the pipes. At the same time, check whether the ground at the toilet installation site is level. Leveling.
2. Determine the center of the sewage pipe
Turn the toilet over, center it on the toilet drain, and draw a cross centerline, which should extend to the bottom of the toilet around the feet.
3. Fixed toilet
Align the crosshairs on the toilet with the sewage outlet on the ground, install the toilet horizontally, press the sealing ring firmly, and install the anchor screws and decorative caps.
4. Do a good job of sealing the bottom
Install a special sealing ring on the toilet sewage outlet, or put a circle of glass glue (putty) or cement mortar around it, and the ratio of cement to sand is 1:3.
5. Install water tank accessories
Run the water for 3-5 minutes to flush the pipeline to ensure the cleanliness of the water pipe; then install the angle valve and connect the hose, then connect the hose to the water inlet valve of the installed water tank accessories and press the water source.
6. Debugging inspection
Check whether the water inlet and seal of the water inlet valve are normal, check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and whether there is any leakage of the water inlet valve filter device, etc.
3. Acceptance of toilet installation project
1. Open the angle valve to check whether there is any leakage at the connection port.
2. Check whether the opening and closing of the automatic valve in the box is flexible.
3. Check the distance between the water level and the overflow pipe after the water in the tank is full.
4. Press both sides of the toilet with both hands, and shake it slightly to see if it is stable.
5. Put a ball of toilet paper in the toilet, open the water hole of the plate to observe the flushing, and check whether there is any leakage at each interface. Rinse and release at least three times in a row. If the discharge is smooth and there is no leakage at each interface, it is qualified.
After the construction of the toilet is completed, we must pay attention to the acceptance to prevent the construction from cutting corners and causing inconvenience to future use. After reading the above introduction about toilet installation and acceptance steps, do you know more about toilet installation and acceptance? If you want to know more about toilets, please continue to pay attention.
