Lifting clothes rack is a furniture product we often use in the family. A good lifting clothes rack is not only because of the brand and cost performance, but also because the installation is reliable and durable. Generally, we should follow the steps when installing the lifting clothes rack, and pay attention to check after installation. Only when the installed lifting clothes rack is reliable and durable, can we rest assured that we use it.
Raising and lowering the clothes rack Installation Method Raising and lowering the clothes rack installation precautions
Installation method of lifting clothes rack
1. Installation of hand rocker:
The hand rocker is generally installed on the right side of the balcony to facilitate habitual use. It is generally 120cm from the ground and fixed with expansion screws according to the height of the user.
2. Installation of the top seat:
On the roof of the balcony to be installed, measure the diameter of the roof light with a steel ruler and mark the installation between 15cm and 30cm on each side of the light (the length depends on the size of the balcony). Then measure the distance between the mark and the edge of the balcony and determine the width of the top seat installation according to this distance. Then the length of the balcony is measured with the lamp as the center, and the two sides of the lamp are evenly divided by 80cm-100cm according to the length of the clothes drying rod. The measured distance between the lamp and the width has four crossing points, which are the installation position of the top seat of the hanger. After the location is determined, drill holes with electric drill. After drilling holes, fix the four top seats with expansion screws (if the rod length exceeds the conventional size, the distance shall be adjusted accordingly).
3. Installation Angle:
The Angle can be installed on the top of the balcony or the top of the wall. The Angle is 50-70cm away from the movable top seat. It must be triangular in the middle of the movable top seat (45 degree Angle) and maintain the same vertical line with the position of the shaking hand installation.
4. Steel wire connection:
There are two steel wires inside a set of clothes rack, first take out one, first put one end of the steel wire through the corner of the bearing steel wire groove, then through the movable end of the top seat of the movable wheel bearing steel wire groove (located in the upper part of the top seat), and then through the fixed end of the top seat of the bearing steel wire groove so that the steel wire is perpendicular to the ground, and then the top cover from the wire into the card cover. The other end of the wire also passes through the corner of the bearing wire groove another hole, and then through the movable seat of another movable wheel bearing wire groove (below the same top seat), so that the wire is perpendicular to the ground, and then the top cover is covered from the wire, and the top cover is stuck. The other wire is installed in the same way.
5, drying rod connection:
At the head end of each wire, thread the drop ball and tie a knot in the drop ball; Then pull the drop ball until it supports the top seat, then pull the wire from the corner, just into a double wire, stuck in one end of the hand; Relax the wire in the hand manipulator, drop the drop ball, put the drying rod through the drop ball, and then tighten and fix the hole in the drop ball, screw the screw; Finally, a plug is installed at both ends of the drying rod.
Attention should be paid to the installation of the lifting clothes rack
1. When hanging the plaster ceiling, the modeling should not be too much, and it should be concave upward, not protruding downward, so as not to affect the slide of the wire rope. When doing modeling, it is necessary to consider the installation of the top seat of the clothes rack. Two pieces of reinforced wood, 5cmX5cm in size and 1.6m apart, shall be reserved. The wood shall be connected with the cement ceiling to strengthen the tension resistance. When buying a ceiling lamp, the size should not be too large, the side length or diameter should not exceed 50cm, because the two drying poles should be arranged on both sides of the lamp, the size of the lamp is too large, the drying pole will be too close to the side, the clothes will touch the wall.
2. In the balcony decoration, we should consider the position of the wall where the hand manipulator is installed, as well as the relationship with the surrounding environment. The owner who wants to arrange the wall cabinet should pay more attention to this point, so as not to install the clothes rack after decoration.
3, drying clothes rack installation is best in the balcony before the last time latex paint installation, repair before, this will not affect the beauty of the wall.
4. After installation, pay attention to all the lines in the hand manipulator and rewind them tightly, which helps smooth operation and avoid card. The wire can be pulled by hand so that it is taut and then shaken.
What do you need to pay attention to when buying and selling clothes racks
The preferred brand, only the brand clothes hanger from the formal manufacturers, only the brand clothes hanger does not use low-grade material, only the brand clothes hanger to ensure quality and service.
Secondly, according to the characteristics of their own balcony selected hanger, automatic lifting drying hanger installation only needs a wall, if the balcony has no top, can choose to push and pull type hanger (as long as there is a wall can be installed). According to the length of the balcony, the size of the drying clothes rack can be selected. The lifting clothes rack has 2.4 meters, 2.7 meters, 2.8 meters, which can be selected. Other installation sizes can be positioned at the time of installation by the workers (can only be shortened on the standard size, not lengthened). Then according to the family situation, personal preferences to choose the style model, hanger has all aluminum, aluminum alloy, stainless steel, titanium alloy, etc., all aluminum high-grade luxury; Aluminum alloy beautiful fashion; Stainless steel is durable and optional.
