The installation of doors and Windows occupies a large proportion in the whole home decoration. Doors and Windows engineering is related to ventilation, lighting, safety and other aspects of the home, and the acceptance of nature can not be careless. Doors and Windows engineering involves a variety of materials and types, so it is necessary to adopt different methods of acceptance according to different materials of doors and Windows. Today, we will tell you about the relevant contents of the door and window engineering inspection process and the acceptance of wood doors and Windows precautions, hope to help you to accept doors and Windows.
Application process of door and window engineering
Experience has proved that beautiful workmanship, material is, beautiful installation can be accepted, professional acceptance also has strict procedures. The acceptance procedures for doors and Windows are as follows:
1. Check the strength of doors and Windows
The thickness of the door, material and specification, sealing; The material, specification and thickness of the window, whether the variety and thickness of the glass is safe, whether the switch of the decoration design window is dexterous, convenient and sealed.
2, check the function of the window
A. Doors and Windows are pushed and pulled smoothly, the surface is smooth and smooth, no serious scratches, and the profiles are not cracked or broken.
B, gold accessories: complete, correct position, firm.
C. Sealing quality: When doors and Windows are closed, there is no obvious gap between the fan and the frame, and the sealing strip is not loose, not falling off, and not exposed.
D, door and window frame, vertical fan, not curved.
E, no pollution of glass, no damage, double glass interlayer no dust and water, uniform separation strip.
F. Is the window drain open? Uncut water will flow into the profile.
Wooden doors and Windows Wooden doors and Windows acceptance precautions
1, the appearance should be beautiful
The surface paint film of wood doors and Windows should be smooth and bright, without falling, bubbles, wrinkles and other quality defects, no corrosion point, dead section, broken residual; Bao door window cover should use wood and door and window fan wood, color coordination, decoration panel and wood line color difference can not be large, the tree species should be the same.
2, doors and Windows can not be deformed
The door and window fan should be square, not warped deformation, door and window fan can just plug the door window frame, and the door and window frame, if the door and window fan and frame gap is large, mainly because the installation of planing is not allowed or the door and window frame and the ground is not vertical, the door and window fan can be removed and planing again, such as the door and window frame is not vertical, should be in the frame plate gasket to find straight.
3, hinge position is correct
The hinge should be located accurately and installed firmly. If the hinge is not on, it will cause the door and window fan and the frame set to be inconsistent, and the door and window switch is not smooth. Each hinge can be first unscrew a screw, and then adjust the door and window fan and the frame of the anastomosis, adjust the repair is correct before tightening all the screws. If the hinge screw is short, or when the screw is nailed in, there is no screw, or screw Angle, will lead to the door and window fan. Appropriate screws should be replaced. The screws must be flat and straight. 1/3 of the screws should be screwed in first, and the rest should be screwed in.
4, the door lock should be appropriate
The opening and locking of the door lock should be smooth, the two parts of the lock on the door and the door frame should be consistent, and the lock is not suitable, which will cause the door switch is not free. The lock tongue plate should be removed, the tongue groove should be repaired with a chisel, and the door frame lock tongue position should be adjusted before installation. In addition, the opening direction of the door should also meet the requirements.
5, doors and Windows should have basic materials
There should be basic material inside the door and window set. When the window cover is made of woodworking board or density board, the basic plate should be fixed on the window frame base keel first, and then nail the line; Door should be made of wood frame, planing, planing straight, and then assembly molding installed on the wall, and then cover the base plate and decorative panel. Knock on the side plate of the door and window set by hand, if the empty drum sound is issued, it means that there is no cushion woodworking board and other basic plate, should be folded and redone.
The above is about the door and window engineering inspection process introduction and wood doors and Windows acceptance precautions related introduction, if you want to know more about the door and window engineering inspection process introduction and wood doors and Windows acceptance precautions related information, please pay more attention to the Fuwojia home network, Fuwojia home network will provide you with more complete, more detailed, updated information.
