HOMENews

Toilet installation method How to do toilet shift

Toilet installation method How to do toilet shift

2023-01-12 04:01:15

The toilet bowl is an important part of the bathroom, if the owners do not know how to install the toilet bowl, it is easy to bury hidden dangers for future use. The following to understand the installation of the toilet bowl method!

First, the installation of the toilet bowl preparation

1. Check the levelness of the floor on which the toilet will be installed. If it is found to be tilted, it can be installed only after it is adjusted to the level.

2, before installation, check the sewage pipe of the toilet, clear the sediment, waste paper and other debris in the sewage pipe.

3. The lower water inlet is kept 2-5 mm above the ground; Prepare for the installation of the toilet bowl.

4. After commissioning and installing the water tank accessories, connect the tap water, inject water into the water tank, and then observe whether the water tank or the water inlet hose leaks for a few minutes; Prepare for the installation of the toilet bowl.

5. The water pressure of tap water is generally stable, and the water tank is filled with water. Test the toilet to see if it flushes well. If the water whirlpool is very fast and rush quickly, it indicates that the water is smooth, otherwise, to check whether there is blockage.

Two, the installation method of the toilet bowl

1. Bolt fixing method

This method is for the bottom of the mounting hole design of the toilet. Put the toilet on the installation position, use a pencil to draw the position of the hole and the bottom wheel corridor on the ground according to the location of the installation hole, then remove the toilet, open the hole in the marked position and insert the exploding bolt, apply adhesive to the joint between the toilet outlet and the ground sewage outlet, put the toilet steadily, firmly pull the exploding bolt, and finally seal the bottom of the toilet with cement mortar.

2, cement bonding method

This method is for the bottom of the toilet design without mounting holes. The toilet is placed on the installation position, use a pencil to draw the bottom of the toilet corridor, along the outline line to lay a circle of wide 30mm, high 15mm cement mortar, the toilet outlet and the ground sewage outlet joint coated with adhesive, wipe the toilet foot, the stable placed in the installation position, make it firmly bonded, wipe the overflow of cement mortar.

After fixing the toilet, wipe the excess cement on the toilet and the ground immediately; Connect the toilet tank to the water supply pipe; Check whether there is leakage in the tank, and then flush to test whether the sewage pipe is clear.

How to do the toilet shift

Toilet displacement, as the name suggests, is to change the position of the toilet in the toilet, which is a lot of home modification is encountered when the problem. But the toilet shift to be careful, otherwise it is likely to lead to awkward situation, such as: after the shift of the toilet water is often not smooth, dirty things can not flow out, and from time to time stink. Today, I will tell you about the matters to pay attention to when the toilet shifts, and the method of the toilet shifts.

Precautions for toilet displacement

The toilet is moved within 10 cm of the toilet several downpipe positions, can not move! Generally, the position of the toilet is changed about 10 cm, with a special toilet shifter. Because the movement is not very large, blockage is less likely to occur. If you have to travel a longer distance, there’s no shifter available, so you have to modify the sewer line.

If you want to move the position a little further, beyond the range of the special toilet shifter can be used, then in the transformation of the pipeline must be elevated the toilet floor and add a trap, trap to prevent the stink back. Since the diameter of the drain pipe is generally 110MM, the floor should be raised by at least 120MM to allow some margin for cement mortar and the slope of the drain pipe.

In addition to considering the problem of blockage, we should also pay attention to the tightness of the pipe. Especially the interface position between different pipelines, to check whether there is leakage, must ensure that there is no leakage, sealing ring, glass glue and so on can not be less.

Summary of four commonly used methods of toilet displacement:

One is to improve the floor;

The second is to transform the original pipe downstairs;

Third, the use of electric toilet for strong drainage;

Four is to use side toilet.

Home toilet transformation toilet need to shift this situation can avoid the best avoid, so as to avoid the future toilet clogging; If it is absolutely necessary to change, it is recommended that the bottom of the pipeline transformation should not take a right Angle, preferably not more than 45 degrees, so as to minimize the probability of pipe blockage.