In foreign countries, the cost of repairing hair is very expensive, because the barber shop not only cannot guarantee the quality, but also expensive, so people will buy the corresponding hair products and build their own. In China, for the sake of convenience, more and more families begin to buy electric hair clippers and complete hair cutting and other work at home. So today Xiaobian is to introduce the information about the two plates of the electric fader hair clipper, including the use of the electric fader hair clipper and troubleshooting steps.
First, how to use the electric Fader clipper
Method of operation of electric fader. There are three basic ways to handle an electric fader:
(1) Hold the middle and upper sides of the fader with the right thumb and index finger, and the other three fingers hold the right rear lateral position and bottom of the electric fader; .
(2) Thumb on the top cover of the electric fader, index finger belly on the side of the push body, palm against the upper right corner of the electric fader, the other three fingers hold the right and bottom of the electric fader,
(3) Support the hand under the electric fader, palm facing forward, thumb and other four fingers respectively hold the left and right sides of the fader. This is sometimes used when reasoning short top hair and bald heads.
No matter which method is used, it has the same operation technique as the hand fader. · It mainly relies on the power of the wrist to make it run. Only the electric fader tooth plate to promote the speed is fast (every second pull back and forth swing about 17 times), and there is obvious vibration, therefore, to grasp the stability, to cooperate closely with the comb, in order to the upper, middle and bottom stubble.
The use of an electric fader cannot make the fader stagger or wobble, because the electric fader moves fast, and a pause will push the hair in that area into a concave shape, while the fader wobble will push the hair on both sides of the range into different lengths. In a word, any negligence and imprudence will bring defects to the hair style.
To use an electric fader to deduce hair, work with a cheat sheet, that is, from the hairline to the outline of the operation. Before the operation, we should first determine the hair style according to the customer’s requirements and head and face shape, and master the customer’s head and facial characteristics and hair quality. Then, from the right sideburns start to operate, the cheat sheet oblique into the root of the hair to hold still, electric faders from the hairline began to use half push method to push out the bottom stubble (that is, the baseline part), to the stubble at the faders gradually suspended, with the copy foil, according to the scheduled hair inclined straight up reasoning out the contour line, temples down copy the Angle and horizontal line is about 300-70. The Angle above the ears falls to about 150-300, and the posterior neck can be mastered at 35. Around the corner. In this way, from right to left, one week in turn, should be pushed with the rib correction, avoid repeating later. On the hair, the middle and bottom stubble should be sloping arc, and the cropping position should be uniform in tone. In reasoning, the Angle of copier and fader should be changed at any time according to the operating position and hair direction. When pushing the feet, the teeth of the fader should gently stick to the scalp, and the rear end of the fader board and the skin should be at an Angle of about 10. Left and right, the Angle is too large, it may be due to the uncontrollable movement of the faders or some obstacles on the scalp of the customer, so that the tooth tip punctured the scalp, the Angle is too small, push the teeth up, will not push the hair.
Operation to the middle and upper stubble parts, the fader gradually suspended, to adjust the Angle of the fader according to the needs of the head and hair style at any time. In the operation, the scalp convex and concave uneven, to use the copy pad, the use of several edge teeth of the fader carving push. When the female pushes, the copy should be accurate. Under the guidance of the copier, the fader should accurately adjust the color even, where thick push, where black push, should not be removed should not be removed hair.
Electric push on the connecting part of the reasoning contour line and the top hair should be matched with a large comb. First of all, the method of full push is used to deduce the connecting part of the contour line. The hair is held up with a large comb, the Angle of the comb is generally parallel to the horizontal plane, and the tooth is slightly tilted inward. Then, the hair tip on the comb tooth is pushed out to the back of the ears, and the large comb is kept at 45. Around the corner. The upward running distance of the large comb should be small and even, and the reasoning should be carried out layer by layer in batches, so that the outline around is curved and the hair tip is clearly layered. If the running distance of the comb is not well mastered, it is easy to cause disconnection or uneven hair length.
In the reasoning of the top long hair, you can stand in the lateral position, horizontal layers of the hair to provoke reasoning, can also be operated from the forehead back, pay attention to the top and the two sides of the joint should have roundness, not out of the corners, leave the length of the hair should be consistent, push the top long hair, should also pay attention to: Thin soft hair is easy to cut off, thick coarse hair is not easy to comb the hair all at once pushed off, in this case, the comb can be used from the outside of the top floating hair comb up a layer, and then push the hair on the back of the pillow, so that there will be no push off the phenomenon. Reasoning long hair, the use of the pillow and the fader should be flexible, different parts, the use of different methods, do not simply hold or lift to push, should be how appropriate to push.
Two, electric fader hair clipper can not cut hair
Possible reasons: (1) the tool head has been seriously worn and needs to be replaced; (2) The tool head lacks lubrication and needs lubrication and maintenance.
Electric hair clipper speed, high lubricating oil requirements. Hair clipper lubricating oil has two categories: mineral oil and synthetic oil two categories, to the full synthetic lubricating oil performance is excellent, clear and transparent, durable, tasteless, winter unchanged thick. Electric hair clippers should use full synthetic hair clipper oil.
The best products to date are Tiger’s Head hotolube and kluber’s all-synthetic hair clipper lubricants. Peach Leopard Leopard has a white bottle of oil can packaging, easy to use.
The durability of mineral oil hair clipper lubricating oil is far less than that of synthetic hair clipper lubricating oil. The smell is larger, the low temperature resistance is not enough, and it will be very sticky in winter. However, the price is cheaper, which is suitable for traditional manual hair clippers.
The use of electric faders hair clippers is relatively convenient, which we can see from the above small series of methods and steps for you to sort out, as long as we follow certain operations, we can basically reach the level of going to the barber shop. That is, if you own an electric fader clipper. However, in the actual adaptation process, many friends will appear electric fader hair clipper hair failure, at this time we can check whether the tool head is seriously worn and processed by replacement or lubrication.
