Basin has become the standard configuration of the toilet, but there are a variety of types of basin, under the basin, basin, hanging basin, column basin and so on, different styles of basin installation method is different, today to talk to you about a variety of basin installation method and basin installation points.
A variety of washbasin installation methods
Table basin installation method
The installation of the platform basin is relatively simple, just according to the installation drawings in the predetermined position of the table hole, after placing the basin in the hole, with glass glue to fill the gap.
Installation method of the lower basin
Under the basin installation is more complex than the platform basin installation, first of all need to be customized according to the size of the basin installation bracket, and then under the basin installed in a predetermined position, fixed support, will have a good hole on the table cover under the basin. Pay attention to the installation, the position of the support should be fixed accurately, in addition, the hole should be rounded.
Mounting method of hanging basin
Hanging basin is usually installed on the wall, very space saving. Let’s take a look at the general installation method of hanging POTS. By measuring, mark the installation height and center line on the finished wall. The recommended installation height is 82cm. Place the basin along the center line to the installation position, adjust it to be horizontally centered, and anchor out the installation hole position on the wall. Open the basin carefully, drill out suspension bolt holes of appropriate distance in the anchor holes on the wall, install the suspension bolts on the wall, and keep each bolt exposed about 45MM to level the basin, cover the gasket and tighten the nut until appropriate, cover the decorative cap and support the wall, correct the position of the anchor hole, and install the support on the wall. Use four pieces of rubber particles to connect the basin with the support together according to the instructions of the purchased water parts, install the faucet and drainage components, and connect the water and drainage pipes between the basin against the wall to seal with mildew proof glue.
Column basin installation method
The general method of column basin installation is to install the launching device of column basin first, and then install the faucet and hose. Then put the porcelain column in the corresponding position, put the column basin on carefully, and pay attention to the water pipe inserted into the original ground set aside. Then connect the upper water pipe to the upper water outlet. Finally, apply glass glue along the edge of the column basin.
Basin installation points
1. Depth is proportional to strength. Water splashing on the body is probably the most uncomfortable point for consumers. As a rule, the depth of the washbasin is directly proportional to the strength of the water running from the faucet installed on it, that is, a deep pool must be equipped with a strong flow of the faucet. Never install thick faucets on the shallow bottom of the pool. This will cause people to splash themselves when they use water. The bottom of the pool should be curved enough, not too flat, or water will accumulate in it.
2, pay attention to the height of whether independent or desktop wash pool, pool surface or table height from the ground should be in 8085 cm, because too short pool will cause people back pain.
3, pay attention to the finish of the pool side must be slightly higher than the table, but with the table must be smooth, the purpose is to splash the water on the table to wipe back into the pool to go unhindered, while convenient for table cleaning. Table itself must choose the surface of the smooth material, the edge and two corners must be smooth, so as not to bump. The smoothness of the washing pool itself is also very important. The high smoothness of the pool surface makes the debris in the water not easy to adhere to the surface, relatively reducing the number of scrubbing.
4, space determines the form of the wash pool is roughly divided into two independent and desktop. Independent beautiful shape, small floor area, and easy maintenance, suitable for small space toilet. However, it needs to be equipped with a mirror or washstand, so that the space above the pool can be used to put some toiletries and cosmetics. A desk sink should take up at least one small desk. It can be put on the table washing utensils, the following cabinet can also put debris. If the bathroom area is not large, you can consider installing a triangular wash pool in the corner, and a triangular debris rack can be hung above the pool to store washing supplies.
The above is to bring you a variety of basin installation methods and basin installation points of attention to the knowledge, I hope to help you.
