A shower is a kind of bathroom equipment for bathing. It is usually installed in our bathroom. It is easy to have a variety of problems with a shower when it is used for a long time. The most common problem is that the water flow in the shower becomes low. When we use the shower, the water becomes less, we can choose to take down the shower, see if there is garbage dirt in the outlet of the shower, and clean it up. Below, let’s take a look at shower repair methods and common failures.
First, after opening the water valve pulse does not spark
热水器故障原因分析
l、水压太低；
2、水过滤器堵塞、花洒头堵塞；
3. The positive and negative electrodes of the battery are inverted;
4、电池电压过低或接触不良；
5, the water inlet and the water outlet are reversed;
热水器保养方法
l. Supercharging water pump;
2. Remove debris;
3.重新安装电池；
4. Reinstall or replace the new battery;
5、重新安装进、出水管；
Two, after opening the water valve pulse light but not fire
热水器故障原因分析
1. There is air in the trachea;
2、电池电压不足；
3、气源开关未打开或进气过滤器堵塞
4, gas type is inconsistent;
5、气体腐蚀后阀门密封上升；
6, cylinder reducing valve output pressure is too high or too low;
热水器保养方法
1, repeatedly switch the water valve to exhaust air until fire;
2. Replace the new battery;
3. Open the air source switch completely or remove the blockage;
4、气体种类不符，禁止使用；
5、更换阀门密封圈；
6、检查、调整输出压力；
Three, the ignition of deflagration sound
热水器故障原因分析
l, cylinder reducing valve pressure is too high;
2、电池电压过低；
3、点火针有积碳或污垢；
4、点火针位置不正确或距燃烧器距离太远；
5. Ignition should be directed at the blockage of the burner hole and nozzle;
热水器保养方法
1. Adjust the pressure of the cylinder reducing valve;
2. Replace the new battery;
3、清除污垢；
4、调整点火针安装位置；
5, remove the air vent and nozzle blocked debris;
Four, the use of water is not hot enough
热水器故障原因分析
1. The cylinder reducing valve is damaged or the gas flow is not enough;
2、气源开关有异物或半堵塞；
3. The gas main switch is half open;
4. The intake nozzle and trachea are too thin or the trachea is too long, resulting in insufficient air flow;
5, gas type is inconsistent;
6、水压过高，水压调节系统故障；
热水器保养方法
1. Replace qualified pressure reducing valve;
2、清除异物；
3. Open the main switch completely;
4. Replace the air nozzle and trachea;
5、请勿使用；
6. Half close the inlet valve to reduce the water pressure;
Five, often flameout in the process of use
热水器故障原因分析
1, water pressure, water pressure fluctuation;
2. Insufficient indoor air supplement;
3. Insufficient battery voltage or poor contact;
4, too little water, too high water temperature, overheating device protection;
热水器保养方法
l、将水扭至适当位置或小水位置；
2. It should be installed again to ensure sufficient air supply;
3. Replace the battery or reinstall it;
4、将水拧至适当位置或水位；
The flame was yellow and there was black smoke
热水器故障原因分析
1. The burner has dirt or its ejector tube has dirt;
2. Cylinder gas is used up;
3. Insufficient indoor air supplement;
4, gas type is inconsistent;
5, the air source pressure is high or low;
热水器保养方法
1、清除污垢和积碳；
2. Replace the cylinder with liquefied gas;
3. It should be installed again to ensure sufficient air supply;
4, do not use;
5, adjust or replace qualified pressure reducing valve
Above, is the shower maintenance method and common faults. A shower is a device that adjusts the flow of water and water itself. It can be used for bathing, washing your hair and rinsing whatever you want. The shower is usually connected to the water heater, and most showers are integrated with the water heater. But now the shower and water heater can also be separate, separate use of safety is relatively high. When we meet a problem, we should choose the right way to solve it, don’t mess around.
