Now many families have also begun to use the shower room, out of the previous toilet bathing era, so when we want to install the shower room, what are the installation points that need to pay attention to? Next, please follow the footsteps of Xiaobian to understand the shower room installation method and shower room purchase guide. Check it out with PChouse.
First, the shower room installation method
1. 获取必要的工具。
2、安装底盆：结合底盆各部件，调整底盆水平，保证盆内和底部没有积水。软管可随距离延长，盆底与排水管牢固连接。
3、测试、防护：安装完毕后，需要进行试水，确保水流畅通。用铅笔和水平仪确定铝材靠墙的钻孔位置，用电锤钻打孔。
4、安装铝条：在钻孔处敲出橡胶颗粒，用螺丝将铝条锁在墙上。
5、固定玻璃：将玻璃夹锁在底盆钻孔处，然后用螺丝固定。
6、安装顶管：在固定玻璃钻孔上方找到合适位置，安装（直式/斜式）固定座并连接顶管。用弯管将其固定在玻璃顶部。
7、安装储物架：将储物架安装在正确的位置，拧紧层压板螺母，固定层压玻璃，并保持垂直和水平。小心铝下面的玻璃防水。
8、安装活动门：安装活动门五金件，将铰链安装在固定门预留孔内。安装完毕后，调整荷叶芯的位置，直至门感觉最佳为止。
9、做好防水：按要求在玻璃侧面或下方安装吸水条或阻水胶带。用硅胶封闭铝材与墙壁、玻璃、底盆之间的接缝。
10、调试、紧固：检查各部位使用是否舒适、顺畅，发现问题应及时调整。调整完毕后，拧紧相应的螺丝，使整个淋浴房更加牢固。
11、收尾工作：将装饰铝条卡入墙铝内，保证其外观干净、大方。最后，需要用抹布将整个淋浴房擦拭干净。
Second, shower room purchase strategy
1. Glass quality is important
For a glass shower room, its quality is the most important.
First of all, we must see whether the glass is transparent, there are no impurities, and the defects of bubbles, because of the process defects or the problem of impure materials, there will always be such defects, and we should pay attention to whether the glass chamfer is smooth and whether the edge is damaged.
Secondly, it is necessary to see whether there is a 3C certification mark on the glass plate, the 3C mark must be fired on the glass, it cannot be labeled, and there is a sequence of factory codes below.
The tempered glass of the shower room is common in 4mm, 6mm, 8mm, 10mm and other specifications, and generally speaking, the tempered glass with a thickness of 6-8mm is the most suitable.
(4) explosion-proof glass is a layer of glue between two layers of glass, there will be no debris after cracking, but tempered glass does not have this function, according to the provisions of tempered glass per 50*50mm area to reach more than 40 pieces.
2. The hardness of aluminum can not be less
The frame of the shower room must be hard enough, and the load bearing must be good enough.
① Aluminum hardness, in order to be able to bear dozens of kilograms of glass weight, the qualified shower room aluminum thickness should be more than 1.2mm, the shower room frame installed on the rail hanging glass should be more than 1.5mm, and the hardness should be more than 13 degrees.
Secondly, it is necessary to see whether the surface of the aluminum is smooth and flat, and whether there is color difference and trachoma
3. Pulley materials should be noted
The pulley is the most frequently used hardware in the shower room, so the quality and tightness of the pulley material are very important.
① First of all, the wheel seat of the pulley should be resistant to pressure and weight, the best is made of 304 stainless steel, high-end synthetic materials, etc. The seal of the wheel seat is better, so that water vapor can not enter, in order to make the wheel smooth.
Secondly, it is necessary to see that the pulley and track need to be closely matched, the gap is small, and it is not easy to fall off, so as to avoid falling off and injuring people.
4. The wall clip should prevent self-explosion
The wall clamp is the hardware connecting the shower room and the wall. The tilt of the wall and the offset of the installation will distort the glass connecting the wall, resulting in the glass self-explosion.
Therefore, the wall clip should have the adjustment function of vertical and horizontal direction, which can make the aluminum material match the distortion of the wall and the installation, eliminate the distortion of the glass, and avoid the self-explosion of the glass.
5. Look at the stability of the rod in the shower room
First of all, the shower room tie rod is divided into: loop tie rod, straight tie rod, diagonal tie rod
The shower bar is the support bar to ensure the stability of the shower room frame, which has an impact on the hardness and strength of the shower room, so we must pay attention to the use of flexible bar when purchasing.
6. Check the water tightness of the shower room
When purchasing the shower room water bar, be sure to test the quality of water tightness, not only near the water bar!
① Check whether there is water seepage between the shower room and the wall
② Water tightness at the hinge and sealing of the rubber strip and the rubber strip
③ Whether the connection between the shower room and the stone base and the bottom basin is sealed
④ After installing the water baffle strip, carry out the water leakage test
7. Design should be human
In addition to the above items, such as whether there is a boutique shelf, sealed magnetic strips, buffer devices, etc., these can provide you with a more comfortable and intimate bath experience design, which should be paid more attention to, and the threshold is too high will make the elderly with mobility difficulties, and children are more troublesome when they enter and leave.
8. Look at the certificate
The most important thing is not to buy those three no products, or unqualified products, so be sure to have three looks when buying:
① Look at the 3c certificate
② Check the quality inspection certificate
Look at the patent certificate
9. Eco-friendly materials are important
For the shower room of acrylic material, it should be noted that some of the glass wires in the composite acrylic plate contain formaldehyde. Acrylic plate is divided into pure acrylic plate and composite acrylic plate, its load-bearing and durability is not the same, but also need to pay attention to when buying.
10. Choose shower room according to room type
The shower room covers a small area, and the bathroom area can be installed as long as there are 3 to 5 square meters. The most common corner type shower room and a zigzag shower room are two, and the specific style to choose depends on the bathroom pattern. The corner shower room is installed in the corner area of the bathroom pattern, and the narrow and long bathroom should choose a zigzag shower room.
11. Although quality is important, installation is not sloppy
The installation of the shower room is also an important link to determine the quality of the shower room, if the installation is unbalanced, the force Angle of the glass is different, it will burst during use.
After reading this article about the shower room installation method explanation with the shower room purchase strategy, I hope to help you.
